What are the advantages of the Edge2000 compared to a hook & loop pad?
Can I use Edge™ Classic pads with backing plates from other manufacturers?
How should I clean Edge™ pads?
What speed is best for buffing with The Edge™?
My distributor doesn't carry The Edge™ products. How can I get them?
Will The Edge2000™ fit onto my buffer?
What detailing chemicals work best with The Edge™ pads?
How does The Edge™ five-color system work?
Why is centering so important?
Is The Edge™ only for automotive use?
How many uses will I get with an Edge™ pad?
What are the best applications for foam and wool pads?
How do I use the Edge2000 system?
How do I take the adapter off the machine?
Which Edge™ pad is best for removing wet sand marks?
Will the adapter ever come through the center and strike the surface?
Which Edge™ pads are best to finish clear coats?
After continual usage my Edge2000 pad seems to loosen and wobble on the adapter.
Why do the edges of the pad appear to peel apart?
The Edge2000 pad seems a little stiffer than a hook & loop pad.
Does Edge2000™ feel the same as a hook & loop-backed pad with a backing plate?
I’m trying to mate the adapter and pad by hand, and it seems difficult.
The release button on the adapter seems very hard to push. I think it’s broken.
Can I adjust the screw in the back of the adapter?
How long will an Edge2000 pad last?
How do I properly care and maintain The Edge2000?
Edge2000 pads seem expensive -- why do you advertise the system as a money-saver?
Q: What are the advantages of the Edge2000 compared to a hook & loop pad?
A:
The Edge2000 is faster, safer, and more economical.
Faster: the Edge2000 systems centers the pad instantly and perfectly every time. With a hook & loop pad, the operator repeatedly tries to center a hook & loop pad only to fail, peel it off, and try again and again. After a few tries he gives up and settles for the best he can do. An Edge2000 is centered every time. There is no settling.
Safer: the Edge2000 has no exposed backing plate that can damage a surface. In fact, there’s no backing plate at all, so you can use the top of the pad to buff under mirrors, spoilers, etc. without having to work upside down in an awkward stance.
Economical: an Edge2000 pad costs less than two single sided hook & loop pads.
Q: Can I use Edge™ Classic pads with backing plates from other manufacturers?
A:
Yes. Other backing plates might not fit as snugly into The Edge™’s recessed back, but they will anchor the pads.
Q: How should I clean Edge™ pads?
A:
While buffing, periodically drag The Edge™ Conditioner brush across the face of the pad to clear out caked-in chemicals. When finished simply rinse with soap and water. Then place back on the buffer and spin dry them. Never machine wash or dry as the heat will weaken the pad’s adhesive backing.
Q: What speed is best for buffing with The Edge™?
A:
The Edge works best between 1500 and 1800 rpm. Never exceed 2000 as this will damage the pad.
Q: My distributor doesn't carry The Edge™ products. How can I get them?
A:
Call us direct at 1-800-315-3343 and we'll help you locate a distributor to service your needs.
Q: Will The Edge2000™ fit onto my buffer?
A:
Yes. The Edge2000™ adapter screws onto any 5/8” thread (US) or 14mm (metric) buffer.
Q: What detailing chemicals work best with The Edge™ pads?
A:
Whatever line you're using now will work fine. Our variety of color-coded textures enables you to mix and match pads with the many chemical lines on the market. Create your own system of chemicals and buffing pads to attack the task at hand.
Q: How does The Edge™ five-color system work?
A:
Each color pad has a different texture. Coarser pads (black and yellow) should be used for compounding and the finer pads are best for polishing and waxing.
Q: Why is centering so important?
A:
First, ergonomics:, because the pad is spinning true, it prevents arm fatigue. When the operator has to fight the machine because it is wobbling, fatigue sets in.
Second, a true-spinning pad gives you a clean, smooth buff without swirl marks.
Third, a true-spinning pad prevents the buffer-s spindle from wobbling, thereby prolonging the life of the machine’s bearings.
Q: Is The Edge™ only for automotive use?
A:
Edge™ pads can be used on not only on cars but also on trucks, boats, planes, even marble and granite -- in fact, virtually any surface that requires buffing.
Q: How many uses will I get with an Edge™ pad?
A:
With proper care and maintenance an Edge™ pad should last an average of 10-15 cars -- or twice that number with The Edge2000™ pad.
Q: What are the best applications for foam and wool pads?
A:
Wool pads typically work best on deep scratches, oxidized paints, wet sand marks and rough finishes where they work faster than a foam pad. Foam pads aren't as aggressive but are easier and cleaner to work with. They are safe for clear coats and have less tendency to produce swirl marks.
Q: How do I use the Edge2000 system?
A:
The system is very easy to use. (you can download illustrated instructions)
To connect the Edge2000:
- Simply screw the adapter onto your buffer BY HAND.
- Line up the hex of the adapter with the center hex of the pad, push down and lock into place.
That’s it -- you’re ready to buff.
To disconnect:
There are two easy ways to remove the pad.
- Holding the spindle in one hand, press the release button with the other thumb and push the pad off from behind with the thumb holding the spindle.
- Or, lay the buffer on a table with the pad facing up, press the release button with your thumb(s) and pull the pad up and off.
Q: How do I take the adapter off the machine?
A:
Putting the adapter on is easy -- simply screw on by hand. But after the spinning of the machine tightens the adapter, use the following procedure to remove it. (NEVER use a tool or wrench to remove the adapter -- this will damage the hexes and the ball bearings, rendering the adapter useless.)
To remove the adapter, simply pop the pad back on, hold the lock button on the machine, and twist off. In other words, use the pad as your wrench to spin the adapter off.
Q: Which Edge™ pad is best for removing wet sand marks?
A:
The black wool pad is the best for removing wet sand marks. Use with an aggressive cutting compound to remove wet sand marks, follow with a green wool or foam pad to polish, and finish with a blue foam pad
Q: Will the adapter ever come through the center and strike the surface?
A:
No. The adapter is designed with a shoulder stop. When the adapter and the plate are mated, the shoulder locks to the bottom of the plate and can’t protrude further. The top of the adapter is recessed below the top of the plastic on the face of the pad and the shoulder prevents it from moving farther. In addition, the foam or wool pad material creates an additional boundary between the surface being buffed and the disk and adapter.
Q: Which Edge™ pads are best to finish clear coats?
A:
The Edge yellow, green, blue and white foam pads are all safe for clear coats.
Q: After continual usage my Edge2000 pad seems to loosen and wobble on the adapter.
A:
The Edge2000 system will loosen a bit after repeatedly snapping on and off the adapter. However, when you spin the pad it will automatically center itself. The pad will absolutely not fly off during usage since the balls on the adapter are anchored in the inner plate of the pad. In fact the foam and/or wool material will wear out and it will be time to change pads long before the inner plate wears out.
Q: Why do the edges of the pad appear to peel apart?
A:
The edges are not coming apart. Edge2000 pads are specifically designed like this to give the operator use of the beveled edge. If the adhesive was brought all the way out to the edge, this would create a hard edge of glue which when buffed against the surface would scratch or damage the surface. Recessing the glue keeps the beveled edge soft and usable without fear of damage.
Q: The Edge2000 pad seems a little stiffer than a hook & loop pad.
A:
Right out of the bag, the Edge2000 pad is stiffer than a hook & loop pad. But that’s not an apples to apples comparison. When you mount the hook & loop pad on a backing plate, the combined hook & loop pad system is actually much stiffer. The Edge2000 pad flexes to give the operator some range with which to maneuver. A hook & loop backing plate, when on a severe angle, actually digs into the face of the foam leaving a circular mark and potentially causing damage. The Edge2000’s flexible inner plate prevents digging or marking on the face of the foam.
Q: Does Edge2000™ feel the same as a hook & loop-backed pad with a backing plate?
A:
You’ll notice a slight difference. The interior plate, while stiff enough to give the firm feel of a backing plate, has the flexibility to maneuver around hard-to-reach areas of a car. Remember, even though it’s flexible, be sure to keep the pad as flat as possible when buffing. Never buff on an angle greater then 10 degrees!
Q: I’m trying to mate the adapter and pad by hand, and it seems difficult.
A:
Mating them by hand is simply for a quick demonstration. Keep in mind that in real conditions the adapter will be screwed on to a machine. The weight and leverage of the machine behind the adapter makes it very easy to engage the pad.
Q: The release button on the adapter seems very hard to push. I think it’s broken.
A:
If you’re just holding the adapter in your hand the release button on the adapter is hard to push. It isn’t designed to be pushed unless it’s mated with a pad. Once the pad is popped on, the balls and inner mechanisms of the drive combine to form a “spring loaded” effect. Then the release button is much easier to operate.
Q: Can I adjust the screw in the back of the adapter?
A:
No. The adapter’s tension is preset at the factory and should not be tampered with. In fact, it is laser imprinted on the side of the adapter “DO NOT CHANGE FACTORY TENSION” This tension is preset to ensure proper engagement of the system under buffing conditions and should never be changed. Adjusting the tension will damage the pad, the surface you’re buffing, or both. Neither Dedication to Detail Inc. nor the distributor will assume any liability for damage caused by tampered adapters.
Q: How long will an Edge2000 pad last?
A:
With proper care and maintenance, the pad should last about 15-20 cars for each side of the pad.
In addition, The Edge2000 adapter will serve significantly longer than a hook & loop plate, which can crack or lose its hook & loop to peeling. An adapter doesn’t have any of those problems. It’s solid machined brass, chrome plated to prevent rust As long as no tools are used on it, it will outlast any plastic plate.
Q: How do I properly care and maintain The Edge2000?
A:
DO NOT machine wash or dry. This will severely limit the life of the pad and may prematurely disengage the adhesive bonding. Simply wash in the sink or by hose with soap and water. To dry the pad, simply pop onto the machine, crank up the RPMs and spin dry.
Q: Edge2000 pads seem expensive -- why do you advertise the system as a money-saver?
A:
When you compare costs over the life of the product, The Edge2000 is more economical in a number of ways.
- Keep in mind that each Edge2000 pad is really two pads in one. When one side is finished, simply flip over and use the other side.
- One Edge2000 pad costs less than two single sided hook & loop pads.
- You’ll save labor cost. The Edge2000 centers instantly, eliminating trial-and-error hook & loop attachment. And both pads are right there; you don’t have to go across the shop to the cabinet only to find that the pad you need isn’t there.
- The Edge2000 is also safer with no exposed backing plate to accidentally strike the surface you’re buffing -- preventing costly damage.
- There’s no stiff backing plate to potentially grind the face of the pad.
- And The Edge2000 prevents operator fatigue that often leads to mistakes.
The Edge2000 system is designed for professional operators who need to maximize profitability and efficiency over the long run.
|
|
|
